~~
.
NS
APPENDIX 1
pis)
ANNEX_T
OPERATIONS ORDER NO, 1-54
SCOPE CONTROLLER INSTRUCTIONS
SCOPE CONTROLLER #1: Will begin his duties when Boundary Tare
excepts contro! of the first rission aircraft. He will monitor VHF
channel B on AN/ARC~1 at scope #1 equipped with URD-2, The AN/ARC-1
will provide automatic guard on D channel ‘mergency). He will monitor
all time hacks on B to assure they are going out over the air.
Upon re~
ceiving a call on D channel, the controller will gqwitch to D as primary
and take bearings on all transmissions on channel D, He will be prepared
to furnish the appropriate scope controller with this bearing or assume
control of aircraft in emergency,
If the emergency requires a Steble
Aircraft Scope Controller #5 will provide Controller #1 with a range, bear~
ing and call sign of appropriate Stable aircraft and switch Stable to
channel D with Yontroller #1 assuming control, Immeciately after H-hour
Controller #1 will switch to D channel as primary end continue to monitor
to receive any emergency calls.
He will be thoroughly familiar with all
emergency procedures in Annex F ‘SAR Plan) and sea conditions in the
sempling area,
Aircraft in emergency and aircraft or ships assisting in
emergencies will be plotted continuously on the operations board to depict
an accurate position and time. Controller #1's teller will be Teller #1
to Plotter #1 to display aircraft in emergency and assisting aircraft.
SCOPE CONTROLLER #2:
Pewter 2 in Annex C
Will begin his duties at start engine time for
(Aircraft Mission Execution Chart). He will check |
scope #2 end VHF channel H to insure they are functioning properly and heve
his teller cheek his commmications with the effects status clerk and
plotter #1. He will monitor VHF channel H from take off for Pewter 2
in Annex C, to receive a call from Pewter 2 when approximately ninety (90)
miles from ENIW°TOK on course to assigned mission station in Annex D
(Aircraft Fehour PosStions and Flight Pattern), When positive control
is established with Pewter 2, the teller wil’ give the status clerk the
time control is accepted and start three minute position reporting to the
plotter. The Controller will give Pewter 2 range and bearing to his
assigned mission station, When Pewter 2 reaches mission station, position
three (3) will be reported to the status clerk, The Comtroller will place
Pewter 2 in a starboard race track pattern with approximately three (3)
minute legs broadside to Ground Zero.
The controller will provide Pewter
2 in a starboard race track pattern with approximately three (3) minute
legs broadside to Ground Zero.
The controller will provide Pewter 2 with
range from Ground Zero each time he passes through his assigned true bearing from Ground “ero, Range will be given on both North and South headings.
The controller will provide position reports and necessary vectors to insure Pewter 2 meeting his "hour position within accepted tolerance of plus
or minus fifteen (15) seconds, Immediately after H-hour, Pewter 2 will
fly at his own discretion to photograph cloud for approximately fifteen
(15) minutes.
The contro'ler will continue to track Pewter 2 and give him
range and bearing to base upon completion of mission.
When Pewter 2 de-
parts cloud area for base, the teller will give position four to the status
clerk.
The Controller will maintain control until control is accepted by
Dirty Face at which time position five will be told to the status clerk,
Scope Controller #2 will have Pewter 2 switch to channel B for the follow~
ing tire hacks:
E = 2 hours and 2 minutes for FE ~ 2 hour time hack
H - 1 hour and 2 minutes for F ~ 1 hour time hack
TASK GROUP 7,4
OPRS ORDER NO. 1-54
ANNEX T, APNDX 2
T-1
aa