CHAPTER II, SECTION 3.
18 inches thick. The wall section projected ap-
USER:
LASL
of 4%4-inch-diameter pipe sleeved holes were in
PURPOSE:
Phonex Measurement
proximately
13
feet above grade. Two rows
the wall section in a pattern aligned with the
PARTICIPATION: 21
Station 1310 and Station 20 to provide lines of
sight through the Station 1310 north wall colli-
DESIGN PSI:
Station 1317.02 was a 17-foot-long reinforced concrete wall, 18 inches thick and 19 feet,
10 inches high on a foundation slab 6 feet wide
and 18 inches thick. The wall section projected
approximately 18 feet above grade. Two rows
of a 5414x22-foot reinforced concrete, earthbarricaded structure located at the Irene terminal of Vacuum Pipeline, Station 1212.02.
work points of the Detector Room Addition at
mator holes.
of four 14-inch-diameter pipe sleeves were in a
pattern aligned with the work points of the Detector Room Addition of Station 1310 and the
holes in the Station 1317.01 wall section and
Station 20 to provide lines of sight through the
Station 1310 north wall collimator holes. Four
rows of angles were attached to the Station 20
side face of the wall to seat lead slab shields.
STATION:
1320
SITE:
Yvonne
USER:
LASL/SC
PURPOSE:
Antenna Station
PARTICIPATION: None
DESIGN PSI:
None
CONSTRUCTION: 4-8-58/4-10-58
80 psi
CONSTRUCTION: 1-29-58/4-26-58
This station was situated in the room space
The space for Station 1410 was 36x16 feet
with a ceiling height of 64% feet. The exterior
walls and one interior division wall separating
Station 1211 were 3 feet thick. The roof and
floor slabs were also 3 feet thick. Station 1410
also provided a timing signal cabinet, field telephone, light fixtures, receptacles, switch panels,
control for an air exhaust fan mounted on a
14-inch-diameter pipe duct through the room
ceiling and fill over. A stock wood door and a
standard blast door were provided at the en-
trance to the room at the end of the interior
’ passage from the outside. Power was furnished
from Station 1525 to the receptacles in the interior passage.
The structure also provided one other room
space for Pinex Recovery Station 1211.
STATION:
1510
SITE:
Nan
USER:
LASL/EG&G
PURPOSE:
Photo Tower Cab
User-furnished antennas were mounted on
a 12-foot steel pipe mast on a concrete base on
the lagoon side of Site Yvonne near Station 1310.
Two pair of timing cables and an underground
2-kw, 110-v single-phase power service were run
to the station.
DESIGN PST:
STATION:
1330
CONSTRUCTION: 4-1-58/7-25-58
SITE:
Elmer
PURPOSE:
Remote Measuring
USER:
LASL
PARTICIPATION: None
DESIGN PSI:
0.75 psi
CONSTRUCTION: 2-22-58/8-16-58
This measuring station was located at the
288-foot level of the 300-foot tower, Station 91.
The entire tower plan section, except at the
elevator shaft, was framed and floored with steel
checker plate. The station was cancelled, how-
ever, after steel erection was completed. A wood
cab was to have been provided within the tower
limits, but it was not constructed.
STATION:
1410
SITE:
Irene
PARTICIPATION: All Bikini Events
None
Utilizing the existing tower cab on the
300-foot tower, Station 90, this station was rehabilitated to the REDWING condition.
STATION:
1511
SITE:
Elmer
USER:
LASL/EG&G
PURPOSE:
Photo Tower Cab
PARTICIPATION: All Eniwetok Events,
Except 1, 2, 15 and 16
DESIGN PSI:
0.75 psi
CONSTRUCTION: 1-11-58/5-31-58
A cab was placed on the top of the 300-foot
tower, Station 91. The original cab in stock was
rejected in favor of a new steel-framed structure, 16x18x12-foot-high. The cab contained
mechanically operated aluminum roll-up doors
Page 103